Huawei FusionCol8000-E24 User Manual Download Page 58

Page: 58 / 269

Figure 4-14 Setting sealing putty

(1) Paper protective film

(2) Sealing putty (standard configuration)

Pipe Anti-freezing

When the ambient temperature is less than or equal to 0°C, drainpipes and water

refill pipes may freeze and thereby be blocked or crack. Take anti-freezing

measures for the pipes.

4.4.6 Removing Transport Fasteners and Desiccant Bags

Procedure

Step 1 Remove the maintenance door of the compressors and take out the desiccant

bags from the compressors.

Step 2 Open the electric control box and take out the desiccant bag from the box.

Step 3 Open the outdoor intake air filter and take out the desiccant bag from the

outdoor air intake compartment.

Step 4 Open the maintenance door and water barrier of the spray pump, and take out

the two desiccant bags from the spray pump compartment.

Step 5 Loosen the transport fixing bolts of the three compressors using a 13# solid

wrench and remove the sheet metal fasteners.

Figure 4-15 Removing sheet metal fasteners from a compressor

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands