Huawei FusionCol8000-E24 User Manual Download Page 152

Page: 152 / 269

Table 9-3 Yearly maintenance checklist

Compone

Item (on the Basis of

Quarterly Maintenance)

Troubleshooting

Sensor

Use a precision T/H sensor to

calibrate the T/H sensors

inside and outside the unit.

If the temperature deviation is

greater than 1°C or humidity

deviation is greater than 5%, the

T/H sensor must be calibrated or

replaced.

Welding

point and

needle

valve

Check that welding points and

needle valves do not leak

using soapy water or check

that they are free from oil

stains.

If leaking points are found, retrieve

the refrigerant and weld the

leaking points again. Contact

technical support.

Exhaust

fan and

indoor

fan

Enter the diagnosis mode,

start the exhaust fan and

indoor fan respectively, and

check whether the fans run

properly without any

abnormal noise.

Replace the fan.

Water

pump

and pipe

Enter the diagnostic mode,

start the water pump and

check whether the water

pump is leaking.

Seal the pipes again.

When the outdoor ambient

temperature is lower than 3°C,

close the water inlet valve,

open the drainage valve

manually, and open the water

pump drainage port using a

17# wrench to drain water.

Open the water inlet valve

when the water pump of the

smart cooling product runs for

the first time every year. After

water is filled and the water

pump starts working,

manually open the exhaust

plug of the water pump to

exhaust air.

NOTE

You are advised to replace the

water pump after the pump has

been running for 20,000 hours.

If the air is not completely

exhausted, air blockage may occur

and the water pump cannot spray

normally. In this case, you need to

manually exhaust air. When the

water pump is running, remove

the exhaust plug on the smart

cooling product. When water flows

out of the exhaust hole, reinstall

and tighten the exhaust plug.

Heat

exchange

r core

When replacing the precooling

module, maintain the heat

exchanger core to ensure the

heat exchange efficiency.

Contact technical support.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

9 System Maintenance

143

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands