Huawei FusionCol8000-E24 User Manual Download Page 85 | Manualshive

Page: 85 / 269

background image

Figure 5-5 Securing the unit

(1) Maintenance door

Step 5 Hoist the other unit.
Step 6 Place it on the top of the installed unit (ensure that the contact surface is clean).
Step 7 Secure the units at the upper and lower layers.
Step 8 Close the maintenance door after the units are secured.

----End

5.4.3 Checking the Refrigerant

Procedure

Step 1 Open the maintenance door to the compressors.
Step 2 Check whether any needle valve bonnet of the compressors is missing.

1. If any bonnet is missing, contact Huawei technical support.
2. If no bonnet is missing, remove the valve bonnets, and press the valve plugs

using the valve bonnets in turn. If gas flows out, the system is normal. If no

gas flows out, contact Huawei technical support.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

76

«
...
83
84
85
86
87
...
»

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

SUPER MULTI NX FDXS09LVJU

Brand: Daikin Pages: 30

Brand: Ionic-CARE Pages: 12

Brand: Stulz Pages: 36

Brand: Stulz Pages: 28

Brand: MCS Master Pages: 19

Brand: Earlex Pages: 6

Silence Force Extreme RO 5823.11

Brand: Rowenta Pages: 80

Montgomery 792849

Brand: Ward Pages: 8

Brand: NADACS Pages: 20

Brand: Dometic Pages: 17

Brand: Electra Pages: 151

Brand: Klimaire Pages: 82

Nexya S4 E Series

Brand: Olimpia splendid Pages: 336

Brand: Amana Pages: 32

Brand: Daikin Pages: 12

Brand: Kerrick Pages: 16

Brand: Hoover Pages: 30

Brand: Lennox Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands