Huawei FusionCol8000-E24 User Manual Download Page 122

Page: 122 / 269

No.

Item

Note

Teamwork control

button

●

indicates that teamwork control is

disabled.

●

indicates that teamwork control is

enabled and no teamwork control alarm is

generated.

●

indicates that teamwork control is

enabled and a teamwork control alarm is

generated.

7.4 Initial Configuration

parameters.

7.4.1 Setting T/H Sensor Parameters

Prerequisites

●

The T/H sensors outside the unit need to be enabled when they are installed;

otherwise, retain the default settings.

●

This section describes how to enable Cold aisle sensor 1.

Procedure

Step 1 On the home screen, choose Settings > System Settings > T/H Sensor.

Figure 7-3 T/H Sensor

Step 2 Set Cold aisle sensor 1 to Enable.
Step 3 Set temperature and humidity parameters.

NO TE

You are not advised to modify the parameters that are not listed in the following table.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

113

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands