Huawei FusionCol8000-E24 User Manual Download Page 4

Page: 4 / 269

Symbol

Description

Indicates a potentially hazardous situation which, if not

avoided, could result in equipment damage, data loss,

performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to

personal injury.

Supplements the important information in the main

text.
NOTE is used to address information not related to

personal injury, equipment damage, and environment

deterioration.

Change History

Issue

Date

Description

2022-04-20

Updated

3.1 Technical Specifications

Updated

2.5 Working Modes

Updated

12 Component Replacement

Deleted the section about installing

electric heater components and cables

because electric heater components are

not supported.

2021-04-15

Building scenario: Added the floor drain

pipe.
Building scenario: Changed the positions

of water refill and drain pipe ports.
Optimized the content related to water

seals.
Building scenario: Updated

4.8

(Optional) Installing Motorized

Dampers and Cables

Added a water pan and float to the

precooling module.
Added the current of the unit and the

corresponding cable model selection.
Added the content about maintenance

for the precooling module and exhaust

fan.
Added

4.6 Installing an Air Deflector

and

5.6 Installing an Air Deflector

2021-01-30

The issue is the first official release.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

About This Document

iii

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands