Huawei FusionCol8000-E24 User Manual Download Page 74

Page: 74 / 269

Locatio

Display Name

Addre

DIP Switch No.

Hot aisle 5 temp/

humid

OFF

Hot aisle 6 temp/

humid

OFF

NO TICE

● The default T/H sensor address is 1.
● After the addresses are set, power on the device, choose Settings > System

Settings > T/H sensor on the home screen of the display module, and set the

sensors in the aisles corresponding to the addresses to Enable. Otherwise, the

sensors will not work.

● If the T/H sensor provided is and has an LCD, bits 1 to 6 of the DIP switch are

used to set the device address, bit 7 is reserved, and bit 8 is used to switch the

temperature display mode.

----End

4.8 (Optional) Installing Motorized Dampers and

Cables

Air dampers must be installed at the indoor air supply and return vents. The air

dampers can be closed to completely isolate the unit from the air duct when the

unit is shut down.

Procedure

Step 1 Install the motorized damper at the air vent of the unit.
Step 2 Install the cables. Connect one end of a cable to the X504 port, route the cable

along the outside of the unit, and reserve the other end near the air damper

actuator.

NO TE

● Ensure that cable routing does not affect the maintenance of the unit.
● Cables must be protected against damage.

Step 3 Connect the air damper cable terminal and air damper actuator terminal.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands