Huawei FusionCol8000-E24 User Manual Download Page 32

Page: 32 / 269

●

The controller provides functions such as automatic recovery after power

failure and water leakage detection, improving the system reliability.

●

The module displays the operating status, time, and other parameters of

components in real time.

●

Multiple display languages are supported.

●

O&M personnel can export fault records in one-click mode, making it easy to

operate the device and know the running status of the device.

●

The device supports communications protocols such as Modbus RTU, Modbus

TCP, and SNMP, facilitating connection to the network management system.

●

The display panel intelligently identifies abnormal parameter settings

(incorrect commands) and rejects them automatically.

2.4 Main Control Module

Appearance

Figure 2-7 Main control module

(1) Running indicator

(2) Alarm indicator

(3) FE_1 port

(4) CAN_IN port

(5) RS485/12V port

(6) USB port

(7) SW button

(8) FE_2 port

(9) CAN_OUT port

(10) COM/FE port

(11) DP port

Indicators

Indicator

Status

Description

Running indicator (RUN) Off

The unit is shut down.

Blinking green

The unit is started.

Alarm indicator (ALM)

Off

There is no alarm, or a

warning or minor alarm

is generated.

Steady red

There is a major or

critical alarm.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands