Huawei FusionCol8000-E24 User Manual Download Page 34

Page: 34 / 269

●

DP port: connects to the display module.

Appearance

DP Port

Connects to the display module for communication and

power supply.

Button

Appearance

SW Button

When the smart cooling product is shut down and the

admin user has logged in, if you hold down the button for

more than 10s, a red frame is added to the button that

involves a risky operation on the display module within 5

minutes. You can press and hold down the button for 10s

to enter the risky operation screen. Exercise caution

because a risky operation may affect system data.

2.5 Working Modes

The unit runs in one of the following modes based on the real-time working

conditions and load.

Table 2-2 Working modes

Working Mode

Fan

Status

Water

Pump

Status

Compressor

Status

Dry mode (fan)

Off

Wet mode (fan + spraying)

Off

Hybrid mode (dry mode +

auxiliary cooling mode)

Off

Hybrid mode (wet mode +

auxiliary cooling mode)

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands