Huawei FusionCol8000-E24 User Manual Download Page 200

Page: 200 / 269

12.18 Replacing a Fan Drive

Prerequisites

●

A drive needs to be replaced.

●

A spare drive of the same model is available and functional.

Context

NO TICE

Before checking and maintaining the device, ensure that the active power supply

to the device is disconnected and the drive has been placed without active power

supply for 10 minutes. Otherwise, electric shocks may occur.

Procedure

Step 1 On the home screen of the display module, tap Shutdown and turn off the unit

switch in the PDF.

NO TICE

Exercise caution because the unit is still energized after it is shut down on the

home screen of the display module.

Step 2 Open the maintenance door.

Step 3 Flip the clip on the fan drive to be replaced.

Step 4 Pull out the handle and remove the fan drive from the subrack.

Figure 12-41 Removing the fan drive

Step 5 Install the new fan drive and insert it into the corresponding slot in the power

distribution subrack.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

191

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands