manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Tab

Parameter

Description

System

Optional

Parts

Return air sensor

Enables or disables a sensor.

Supply air sensor

Enables or disables a sensor.

Cold aisle sensor

Enables or disables a sensor.

Hot aisle sensor

Enables or disables a sensor.

Outdoor intake air

sensor 3

Enables or disables a sensor.

Cold aisle

temperature and

humidity sharing

This function can be enabled only

when at least one smart cooling

product in the teamwork group is

equipped with cold aisle T/H sensors. If

this function is enabled, the master

unit in the teamwork group collects

the cold aisle temperature and

humidity values from all units

equipped with cold aisle sensors, and

synchronizes the temperature and

humidity control type and setpoints to

all slave units.

Hot aisle temperature

and humidity sharing

This function can be enabled only

when at least one smart cooling

product in the group is equipped with

hot aisle T/H sensors. If this function is

enabled, the master unit in the

teamwork group collects the hot aisle

temperature and humidity values from

all units equipped with hot aisle

sensors, and synchronizes the

temperature and humidity control type

and setpoints to all slave units.

Supply air damper

● Disable: The air damper function of

the unit is disabled.

● AO Ctrl: Select AO Ctrl for AO-type

air dampers.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

104

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Makita CL183D Technical Information preview
CL183D
Brand: Makita Pages: 7
eta Grande Animal Instructions For Use Manual preview
Grande Animal
Brand: eta Pages: 44
Martin airconditioningcentre KFR-23IW/AG Installation And Repair Manual preview
airconditioningcentre KFR-23IW/AG
Brand: Martin Pages: 17
Equator CSM 2100 Owner'S Manual preview
CSM 2100
Brand: Equator Pages: 11
SPT WA-1300E Instruction Manual preview
WA-1300E
Brand: SPT Pages: 20
TriStar AC-5521 Instruction Manual preview
AC-5521
Brand: TriStar Pages: 72
ECRON 15KC User Manual preview
15KC
Brand: ECRON Pages: 44
DELLA 048-GM-48382 User Manual preview
048-GM-48382
Brand: DELLA Pages: 20
Quietside QS36-VJ220 Owner'S Manual Install Manual preview
QS36-VJ220
Brand: Quietside Pages: 15
Vacmaster EasyClean SCA0801 Manual preview
EasyClean SCA0801
Brand: Vacmaster Pages: 16
H-P Products TURBINE POWERHEAD and HAND HELD TURBINE... Instruction Manual preview
TURBINE POWERHEAD and HAND HELD TURBINE...
Brand: H-P Products Pages: 10
Rasonic RC-X7R Operation Manual & Installation Manual preview
RC-X7R
Brand: Rasonic Pages: 24
Shark V3800 Series Owner'S Manual preview
V3800 Series
Brand: Shark Pages: 16
Disan DS A01 Owner'S Manual preview
DS A01
Brand: Disan Pages: 22
Linea DOMO DO7279S Instruction Booklet preview
DOMO DO7279S
Brand: Linea Pages: 48
camry Premium CR 7039 User Manual preview
Premium CR 7039
Brand: camry Pages: 64
Graymills OSEP-2 Operation And Maintenance Instructions preview
OSEP-2
Brand: Graymills Pages: 4
Trotec PAC-W 2600 SH Operating Manual preview
PAC-W 2600 SH
Brand: Trotec Pages: 23

Brands by name

Popular brands

Load more brands