Huawei FusionCol8000-E24 User Manual Download Page 149

Page: 149 / 269

Table 9-1 Monthly maintenance checklist

Item

Expected Result

Troubleshooting

Air filter

The air filter is not damaged

or distorted.

Replace the air filter.

Water

tank

The float has no scale.

Clean up the scale on the liquid

level sensor when the device is

shut down.

The water tank filter is not

blocked.

Clean up the foreign matter on the

surface of the water tank filter.

Compresso

The compressor is secured.

Tighten screws if the compressor is

not secured.

The operating compressor

generates no metal friction

noise or collision noise from

inside.

Replace the compressor.

Pipe

The refrigerant pipe does not

leak or corrode, and is

properly wrapped with

thermal insulation foam.

Repair the leakage points and

rewrap thermal insulation foam.

Wear working gloves and

touch the needle valve and

soldering points of the

refrigerant pipe. There are no

oil stains.

If there are oil stains, check

whether the suction and discharge

pressure of the compressor is

within the normal ranges. If the

pressure is beyond the normal

range, contact technical support.

No water exists under the

water pipe or on the thermal

insulation foam.

● If drops of water are evenly

distributed, wipe them off with

dry cloth.

● If there are large water marks,

close the water inlet sluice and

handle the leaking points. If the

thermal insulation foam is

damaged or missing, install new

thermal insulation foam.

The refrigerant pipe support

is secure and intact.

Replace the pipe support and

secure it again.

Indoor fan

and

exhaust

fan

The guards of the indoor fan

and exhaust fan are not

deformed, and the fan blades

are not damaged.

Replace the fan.

The indoor fan and exhaust

fan run smoothly.

Take out the foreign matter if the

fan is blocked.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

9 System Maintenance

140

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands