manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Networking

FE Teamwork

FE Monitoring

Note

A teamwork network supports

a maximum of 16 units.

● In the independent wiring

scenario, retain the default

value Independent wiring

for Monitor FE wiring

mode on the Access

Control screen of each

unit.

● In the shared wiring

scenario, set Monitor FE

wiring mode to Shared

wiring on the Access

Control screen of each

unit.

 

NO TE

Customers can purchase a switch and NetEco as the monitoring system.

Figure 5-25 Connecting communications cables (independent wiring)

Figure 5-26 Connecting communications cables (shared wiring)

If the length of a network cable in the FE teamwork is greater than or equal to

100 m, use the group-based ring networking mode.
1. Connecting units with odd numbers: Connect the FE_1 port of the unit with

an odd number to the FE_2 port of the unit with the next odd number.

2. Connecting units with even numbers: Connect the FE_2 port of the unit with

an even number to the FE_1 port of the next unit with an even number.

3. Connect FE_2 of No. 1 unit and FE_1 of No. 2 unit, and connect the remaining

FE_1 and FE_2 of the last two units.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

91

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Makita VC4210M Manual preview
VC4210M
Brand: Makita Pages: 33
Makita VC3211M Technical Manual preview
VC3211M
Brand: Makita Pages: 18
Makita VC3012L Original Operating Instructions preview
VC3012L
Brand: Makita Pages: 14
Makita VC1310L Technical Information preview
VC1310L
Brand: Makita Pages: 23
Makita DVC260 Technical Information preview
DVC260
Brand: Makita Pages: 11
Makita DRC300 Quick Start Manual preview
DRC300
Brand: Makita Pages: 12
Makita DRC200 Quick Start Manual preview
DRC200
Brand: Makita Pages: 2
Makita DCL140 Technical Information preview
DCL140
Brand: Makita Pages: 9
Makita 448 Manual preview
448
Brand: Makita Pages: 33
Makita 447 L Manual preview
447 L
Brand: Makita Pages: 102
Zibro S185 Operating Manual preview
S185
Brand: Zibro Pages: 102
Parkside PNTS 1500 B2 Translation Of Original Operation Manual preview
PNTS 1500 B2
Brand: Parkside Pages: 84
Wagan 7205 User Manual preview
7205
Brand: Wagan Pages: 4
d2itsu APD-9CR User Manual preview
APD-9CR
Brand: d2itsu Pages: 20
Lennox MS7 Quick Manual preview
MS7
Brand: Lennox Pages: 12
Lennox LI036CI-180P432 Service Manual preview
LI036CI-180P432
Brand: Lennox Pages: 100
Scarlett SC-VC80H19 Instruction Manual preview
SC-VC80H19
Brand: Scarlett Pages: 16
Gree CA145006400 Service Manual preview
CA145006400
Brand: Gree Pages: 73

Brands by name

Popular brands

Load more brands