Huawei FusionCol8000-E24 User Manual Download Page 179

Page: 179 / 269

Figure 12-21 Protective cover

(1) Protective cover

Step 6 Pull out the two fans horizontally.

●

If the first fan needs to be replaced, remove the bolts between the first and

second fans, and replace the fan.

●

If the second fan needs to be replaced, the latch is stuck when you pull out

the second fan. Press the latch and pull out the fan horizontally.

NO TICE

Two persons are required to pull out the fan.

Step 7 Unscrew the fan support and take out the fan.

Figure 12-22 Removing a fan

(1) Latch

Step 8 Remove the six screws that secure the fan to the fan support to separate the fan

from the fan support.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

170

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands