quick start guide
English
SR8950
Code No. DJ68-00637Q REV(0.0)
Keep in mind!
How to turn on the power switch?
X
When you initially purchase the product, the power
switch will be kept off. Turn on the power switch at
the bottom of the cleaning robot.
All functions will work only when the power switch
is turned on. Lift the body and turn on the power
switch while making sure not to press any other button.
NOTE
If you turn off the power switch, all settings except for the
current time and the Weekly reservations are reset.
Battery is naturally discharged!
X
When you separate the cleaning robot from the charger, the battery
will naturally be discharged. Therefore keep the cleaning robot on the
charger, if possible.
NOTE
If no key is pressed for approximately 1 minutes after turning
the power on, the power is automatically cut to prevent the
battery discharging. To turn the power on again, press and
hold the power (Run/Stop) button on the main body.
Auto charge is not smooth!
X
When you execute the cleaning mode while the cleaning robot is
charged on the charger, it will return to automatically charge more
quickly and accurately.
1. In the following cases, lift the cleaning robot with your hand and put it
on the charger to charge it.
-
When the charger is installed in a corner.
-
When the battery is fully discharged.
-
When the cleaning robot is trapped with an obstacle.
-
When the cleaning robot cannot pass over the doorsill to the location
where the charger is installed.
2. When the charger and the cleaning robot are in separate rooms, it
could take a long period of time to automatically charge the robot.
3. Check the installed condition of the charger.
(Refer to Installing the charger)
4. Wipe the obstacle sensor window lightly with a soft cloth.
NOTE
To test the auto Homing, press the Charge button when the
cleaning robot is within 1.5M of the charger.
The cleaning robot cannot cross over the
doorsill!
X
The vacuum cleaning robot innovative
driving system makes it possible for it to
cross over doorsills with a height of about
1cm and clean all rooms. The vacuum
cleaning robot may not be able to pass a
1cm doorsill depending on the shape of the doorsill.
What do I do when the suction power is low
or the noise level is high?
X
Clean the dust bin and fi lter.
X
Clean the power brush.
The cleaning robot hits the obstacles such as
wall, furniture etc.
X
The cleaning robot can bump into chair legs, table legs, sofa etc.
during the operation. Put the chair on top of the table while cleaning.
The cleaning robot is not able to clean the
corners!
X
Because the cleaning robot cannot
completely clean the tight corners, wall
between the sofas you should regularly
clean those areas.
There is a weird noise!
X
After turning off the power switch on the bottom, fl ip the cleaning robot
and remove any foreign substances (Paper, vinyl) on the power brush
or air pump.
Charging time is too long!
X
If you charge the cleaning robot when the battery is heated after the
cleaning, the charging time could take longer.
Troubleshoting for Error Codes
ERROR
CODE
CAUSE
SOLUTION
•
Vacuum cleaning robot is
caught, stuck or trapped
while navigating.
•
Turn off the Power Switch
at the bottom and move
the robotic vacuum cleaner
to a different location.
•
A foreign substance (string,
paper, toy etc.) is caught
in the power brush.
•
Turn off the Power Switch
at the bottom and remove
the foreign substance from
the power brush.
•
A foreign substance (string,
paper, toy etc.) is caught
in the left driving wheel.
•
Turn off the Power Switch
at the bottom and remove
the foreign substance from
the left driving wheel.
•
A foreign substance (string,
paper, toy etc.) is caught
in the right driving wheel.
•
Turn off the Power Switch
at the bottom and remove
the foreign substance from
the right driving wheel.
•
Check the Bumper sensor.
•
Turn off the Emergency
Stop switch at the bottom,
and then remove the
obstacle from the front of
the vacuum cleaning robot
or move it to a different
location.
•
A foreign substance
(dust, stain etc.) is on the
Obstacle sensor window.
•
Turn off the Power Switch
at the bottom and wipe
the foreign substance from
the front and rear sensor
windows using a soft
cloth.
•
A foreign substance (Dust,
stain etc.) is on the Cliff
sensor window.
•
Turn off the Power Switch
at the bottom and wipe
the foreign substance on
the cilff sensor window
with a soft cloth.
•
Dust bin not inserted.
•
Insert the dust bin until you
hear a “Click” sound.
•
A foreign substance
(String, cloth etc.) is caught
on the edge-cleaning side
rotating brush.
•
Turn off the Power Switch
at the bottom and wipe
the foreign substance from
the edge-cleaning side
rotating brush.
✽
If you press the Start/Stop button or turn off the Power Switch, the error
code is cleared.
Stair
Stair
type
type
About 1cm
Vertical
Vertical
type
type
DJ68-00637Q-1 EN.indd 01
DJ68-00637Q-1 EN.indd 01
13. 01. 07 오후 5:34
13. 01. 07 오후 5:34