Huawei FusionCol8000-E24 User Manual Download Page 236

Page: 236 / 269

Paint Damage

Tools and

Materials

Procedure

Description

Dent

1. If a dent is less than 100 mm

in area and less than 3

mm in depth, fill the dent with Poly-Putty base and then

perform the same operations as those for processing deep

scratches.
2. If a dent is greater than 100 mm

in area or greater than

3 mm in depth, ask the local supplier for an appropriate

repainting solution.

Procedure

Step 1 Gently polish the damaged areas using fine sandpaper (minimum grit size: 180) to

remove smudges or rust.

Figure B-1 Polishing a damaged area using sandpaper

Step 2 Dip a piece of cotton cloth into anhydrous alcohol and wipe the polished or

damaged area to remove the dirt and dust. Then wipe off the alcohol with a clean

and dry cotton cloth.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

B Repainting the Unit

227

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands