manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

13.2.6 How Do I View Version Information?

Procedure

Step 1 On the home screen, tap About.

Step 2 On the About screen, tap Version Info or E-label.

NO TE

● The Version Info screen displays detailed version information about the control board,

SPD and voltage detection board, and exhaust fan. The E-label screen displays detailed

information about the system, control board, SPD and voltage detection board, and

exhaust fan.

● When the cold and hot aisles of T/H boards are enabled, the information about the

corresponding cold and hot aisles is displayed on the T/H Board under About > Version

Info or T/H Board under About > E-label.

● When the cold and hot aisles of T/H boards are disabled, the information about the

corresponding cold and hot aisles is not displayed on the T/H Board under About >

Version Info or T/H Board under About > E-label.

----End

13.2.7 How Do I View the Service Information?

Procedure

Step 1 On the home screen, tap About.

Step 2 On the About screen, tap Service Info.

Figure 13-10 Service Info screen

----End

13.2.8 How Do I Check Teamwork Control Information?

Procedure

Step 1 On the home screen, choose 

 > 

 to display the teamwork information of

the current group.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

13 FAQ

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

209

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Daewoo RCP-1000 Owner'S Manual preview
RCP-1000
Brand: Daewoo Pages: 12
Parkside PNTS 1500 B2 Translation Of Original Operation Manual preview
PNTS 1500 B2
Brand: Parkside Pages: 84
Qlima S42 Series Operating Manual preview
S42 Series
Brand: Qlima Pages: 50
KeepRite DLFCAB Installation Instruction preview
DLFCAB
Brand: KeepRite Pages: 16
Scarlett SC-VC80C01 Instruction Manual preview
SC-VC80C01
Brand: Scarlett Pages: 15
Mammoth xC User Manual preview
xC
Brand: Mammoth Pages: 19
NSS PACER 12UE Operator'S Manual preview
PACER 12UE
Brand: NSS Pages: 16
Vaillant V 12-025 HWI Training Manual preview
V 12-025 HWI
Brand: Vaillant Pages: 48
Advance acoustic 107404753 Instructions For Use Manual preview
107404753
Brand: Advance acoustic Pages: 20
Carrier 22023011003834 Installation Manual preview
22023011003834
Brand: Carrier Pages: 37
Forbes Trendy - Wet & Dry User Manual preview
Trendy - Wet & Dry
Brand: Forbes Pages: 18
Thomas PET & FAMILY Aqua+ Instructions For Use Manual preview
PET & FAMILY Aqua+
Brand: Thomas Pages: 30
Bissell 89Q9/18Z6 series User Manual preview
89Q9/18Z6 series
Brand: Bissell Pages: 20
REMEZA RFD 1000 Instruction Manual preview
RFD 1000
Brand: REMEZA Pages: 29
Quadro AC-35CH-FC BIO Iceberg Installation Manual preview
AC-35CH-FC BIO Iceberg
Brand: Quadro Pages: 32
EUROM 379990 Instruction Manual preview
379990
Brand: EUROM Pages: 100
dirna Bergstrom Bycool DINAMIC 1.1 Users Handbooks preview
Bycool DINAMIC 1.1
Brand: dirna Bergstrom Pages: 36
Acson ACC 10C Technical Manual preview
ACC 10C
Brand: Acson Pages: 203

Brands by name

Popular brands

Load more brands