Huawei FusionCol8000-E24 User Manual Download Page 158

Page: 158 / 269

Symptom

Possible Cause

Solution

The compressor

discharge

pressure is too

low.

The refrigerant is insufficient. Charge more refrigerant.

Refrigerant leaks.

Check the pipeline for

leakage.

The exhaust fan drive fails to

be controlled.

Replace the fan drive.

The compressor

suction pressure

is too low or

liquid returns.

The refrigerant is insufficient. Charge more refrigerant.

The indoor temperature is set

too low.

Modify the temperature

setting.

The air filter is dirty or

blocked.

Replace the air filter.

The external residual

pressure is too high, and

airflow decreases.

Check whether the air

channels are blocked.

The condensing pressure is

too low.

Check the condenser.

The compressor

generates a

loud noise.

Liquid is returning to the

compressor.

Check whether the oil

temperature and discharge

temperature are within

normal ranges.

Refrigerant oil is insufficient.

Add refrigerant oil.

The sheet metal fasteners for

securing the compressor

during transportation are not

removed.

Remove the sheet metal

fasteners.

The fan fails to

start.

The switch of the fan is

turned off.

Check the switch of the fan.

The fan is damaged.

Replace the fan.

The interconnection

terminals for the fans are not

securely connected.

Secure the interconnection

terminals.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

10 Troubleshooting

149

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands