Huawei FusionCol8000-E24 User Manual Download Page 51

Page: 51 / 269

Figure 4-4 Concrete platforms for combined units (unit: mm)

(1) FusionCol8000-E

(2) Concrete platform

Step 2 Determine the reference points for installing a unit on the concrete platforms.

Mark the reference points using a marker.

Step 3 Mark the mounting positions for the four corner fittings of the unit using an ink

fountain and long measuring tape.

NO TICE

When marking the mounting positions for corner fittings, ensure that the four

lines form a rectangle.

Step 4 Place the shock absorption pads at the corresponding positions of corner fittings

on the concrete platforms.

Step 5 Adjust the unit in the required direction, connect the steel hoisting ropes, and

hoist the unit onto the concrete platforms.

NO TICE

When hoisting the unit, ensure that the four corner fittings of the unit are aligned

with the marked mounting positions for corner fittings on the concrete platforms.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands