Huawei FusionCol8000-E24 User Manual Download Page 141

Page: 141 / 269

Figure 7-17 Wizard Startup

NO TE

After commissioning for a component succeeds, the system automatically performs

commissioning for the next component you selected. Please wait during the

commissioning.

2. Check the commissioning result.

–

If the message "Commissioning succeeded" is displayed in the lower left

corner, tap Confirm. The home screen is displayed.

–

If the message "Commissioning failed" is displayed in the lower left

corner:
i.

Click the link at "Commissioning failed" to view the failure cause, tap

Back and Confirm, and troubleshoot based on the failure cause.

ii. On the home screen, choose Maint > Wizard Startup and perform

commissioning again.

Figure 7-18 Wizard-based startup result

----End

7.7 (Optional) Power-Off

Context

In shutdown mode, the Shutdown button is green (unavailable) and the Start

button is gray (available).

Procedure

Step 1 Tap Shutdown on the home screen of the display module. A warning is displayed,

indicating whether to shut down the unit.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

132

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands