Huawei FusionCol8000-E24 User Manual Download Page 212

Page: 212 / 269

Step 2 Check that is displayed in the status bar of the home screen, indicating that the

USB flash drive is successfully identified.

Step 3 Select an operation in USB Operations and perform the operation as prompted.

Figure 13-2 USB Operations

Step 4 Tap Remove USB to remove the USB flash drive in safe mode.

Step 5 Remove the USB flash drive and set it aside.

----End

13.1.1 How Do I Export Data?

Context

With the one-click mode, you can export active alarms, historical alarms, run logs,

and so on.

Procedure

Step 1 Choose Maint > USB Operations > Export to enter the Select Path screen.

Figure 13-3 Select Path

Step 2 On the Select Path screen, specify the save path and tap Next. In the displayed

dialog box, tap Yes.

Step 3 After the data is successfully exported, tap Finish.

Step 4 On the home screen, choose Maint > USB Operations > Remove USB to remove

the USB flash drive in safe mode.

----End

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

13 FAQ

203

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands