Huawei FusionCol8000-E24 User Manual Download Page 166

Page: 166 / 269

Step 3 Replace the indoor return air filter (side). Open the maintenance door

corresponding to the air filter, remove the fastener from the air filter, and pull out

the air filter.

Figure 12-7 Replacing an air filter

Step 4 Install a new air filter and secure it.

Step 5 Install the air filter fasteners.

Step 6 Power on the unit, choose Maint > Performance Maint on the home screen of

the display module, and clear the total runtime of the air filter.

Step 7 Tap Start on the home screen. Ensure that the unit is running normally without

any alarms.

----End

12.5 Replacing a Differential Pressure Switch (Building

Scenario)

Prerequisites

●

A differential pressure switch needs to be replaced.

●

A spare differential pressure switch of the same model is available and

functional.

●

Tool: Phillips screwdriver

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

157

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands