Huawei FusionCol8000-E24 User Manual Download Page 203

Page: 203 / 269

Figure 12-44 Removing a liquid level sensor

(1) Fastener

(2) Liquid level sensor

Step 5 Install the new liquid level sensor and tighten it to a torque of 5 N·m. Install the

fastener and connect the interconnection terminal of the liquid level sensor.

Step 6 Power on the unit and tap Start on the home screen. Ensure that the unit is

running normally without any alarms.

Step 7 Install the maintenance door and water baffle plate for the fan.

----End

12.20 Replacing a Water Pump

Prerequisites

●

A water pump needs to be replaced.

●

A spare water pump of the same model is available and functional.

●

Tools: flat-head screwdriver, Phillips screwdriver, socket wrench

NO TICE

Before replacing the water pump, drain water from the water tank completely.

Procedure

Step 1 On the home screen of the display module, tap Shutdown and turn off the unit

switch in the PDF.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

12 Component Replacement

194

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands