Huawei FusionCol8000-E24 User Manual Download Page 50

Page: 50 / 269

Stage

Precautions

Ensure that the crane is properly located and avoid long-

distance hoisting.

Keep the unit stable and horizontal during hoisting, and

ensure that the diagonal gradient of the unit is within 5

degrees.

Lift and land the unit slowly to prevent shock to devices

inside it.

Remove the steel ropes after ensuring that the unit is

placed evenly on the concrete platforms.

Tools: marker, ink fountain, long leather measuring tape, crane, socket wrench,

torque wrench, Phillips screwdriver, jack, steel hoisting rope, level, level gauge,

hammer drill, angle ruler, claw hammer, vacuum cleaner
Materials: unit to be hoisted, expansion bolt, angle steel bracket

Procedure

Step 1 Prepare concrete platforms.

Figure 4-3 Concrete platforms for a single unit (unit: mm)

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands