manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

4.3 Materials

Table 4-1 Material description

Item

Description

Type

Standard

material

This type of materials is

delivered with the unit and

can be obtained from the

fittings bag.

Materials in the packing list

Auxiliary

material

Customers can purchase this

type of materials from the

supplier or other vendors.

Cables

Optional

material

Customers can purchase this

type of materials from the

supplier based on application

scenarios.

T/H sensor, water sensor,

smoke sensor, and air damper

Engineering

purchase

material

Customers need to purchase

this type of materials by

themselves.

Drainpipe, water refill pipe,

pipe support, air duct, and

equipotential ground lug or

cable

 

4.3.1 Water Refill Pipe and Drainpipe

Table 4-2 Pipe specifications

Item

Connector

Spray water refill pipe

G 3/4 inch external thread connector

Condensate water pan drainpipe of

the evaporator

G 3/4 inch external thread connector

Spray drainpipe

G 1-1/2 inch external thread connector

Condensate pan drainpipe of the heat

exchanger core

G 1 inch external thread connector

 

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

38

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Samsung AW0750 Manual De Instrucciones preview
AW0750
Brand: Samsung Pages: 14
Samsung AVMWC020CA0 Owner'S Instructions Manual preview
AVMWC020CA0
Brand: Samsung Pages: 16
Samsung AVMBH020EA4 Owner'S Instructions Manual preview
AVMBH020EA4
Brand: Samsung Pages: 16
Samsung AQV07PSBN User & Installation Manual preview
AQV07PSBN
Brand: Samsung Pages: 43
Samsung AQB09JJWC User Manual preview
AQB09JJWC
Brand: Samsung Pages: 26
Samsung AQ09U Series User Manual preview
AQ09U Series
Brand: Samsung Pages: 34
Samsung AQ07P8GE Owner'S Instructions Manual preview
AQ07P8GE
Brand: Samsung Pages: 26
Samsung AP-L1831 Manual preview
AP-L1831
Brand: Samsung Pages: 36
Samsung ASHM070VE Owner'S Instructions Manual preview
ASHM070VE
Brand: Samsung Pages: 26
Samsung AS12UUPN Installation Manual preview
AS12UUPN
Brand: Samsung Pages: 40
Samsung AS070VE Owner'S Instructions Manual preview
AS070VE
Brand: Samsung Pages: 24
Samsung AJ009JNNDCH FJM series Service Manual preview
AJ009JNNDCH FJM series
Brand: Samsung Pages: 118
Samsung AVXWNH022EE User Manual preview
AVXWNH022EE
Brand: Samsung Pages: 34
Samsung AVMKC020CA0 Manual De Instrucciones preview
AVMKC020CA0
Brand: Samsung Pages: 16
Kärcher T 8/1 Classic Manual preview
T 8/1 Classic
Brand: Kärcher Pages: 24
Filters Fast FF-CAP-01 Product Manual preview
FF-CAP-01
Brand: Filters Fast Pages: 10
Klimaire KSIO User Manual preview
KSIO
Brand: Klimaire Pages: 16
Magio MG-892 Instruction Manual preview
MG-892
Brand: Magio Pages: 28

Brands by name

Popular brands

Load more brands