Huawei FusionCol8000-E24 User Manual Download Page 114

Page: 114 / 269

Tab

Parameter

Description

Supply air damper

shutdown mechanism

● Close for fans: The fire dampers

and air dampers are open or closed

depending on whether fans are

started or shut down.

● Close for system shutdown: The fire

dampers and air dampers are open

or closed depending on whether the

unit is started or shut down.

● Close for fire: The fire dampers are

closed only when a smoke or fire

alarm is generated. By default, the

fire dampers are open.

NOTE

This parameter is displayed when AO

Ctrl is selected for Supply air damper.

Return air damper

● Disable: The air damper function of

the unit is disabled.

● AO Ctrl: Select AO Ctrl for AO-type

air dampers.

Return air damper

shutdown mechanism

● Close for fans: The fire dampers

and air dampers are open or closed

depending on whether fans are

started or shut down.

● Close for system shutdown: The fire

dampers and air dampers are open

or closed depending on whether the

unit is started or shut down.

● Close for fire: The fire dampers are

closed only when a smoke or fire

alarm is generated. By default, the

fire dampers are open.

NOTE

This parameter is displayed when AO

Ctrl is selected for Return air damper.

Exhaust air damper

● Disable: The air damper function of

the unit is disabled.

● AO Ctrl: Select AO Ctrl for AO-type

air dampers.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

105

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands