manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Refrigerant Frostbite

Refrigerant leakage may cause frostbite. Take protective measures (for example,

wear antifreeze gloves) when handling refrigerant.

Storage and Recycling

●

Do not store devices near a heat source or under direct sunshine.

●

Keep devices away from fire or high-temperature objects, especially devices

injected with pressurized nitrogen or refrigerant; otherwise, explosion or

refrigerant leakage may occur, causing personal injury.

●

 The sign indicates that the product cannot be disposed of with other

wastes that have a shell in European Union (EU) areas. To avoid environment

pollution and harm to human health, wastes must be classified and recycled.

This also promotes resource reuse. When recycling a device, fill in the device

information in the recycling collection system or contact your dealer for help.

The dealer can help you recycle devices in a safe and environment-friendly

way.

1.7 Others

Exercise caution when shutting down the smart cooling product. Doing so may

cause equipment and room overheating, which will damage the equipment.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

1 Safety Information

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

11

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

GE AZ61H12DAB Owner'S Manual And Installation Instructions preview
AZ61H12DAB
Brand: GE Pages: 72
Panasonic CS-KS30NKU Technical & Service Manual preview
CS-KS30NKU
Brand: Panasonic Pages: 108
Panasonic CS-A12PKD Service Manual preview
CS-A12PKD
Brand: Panasonic Pages: 140
Daikin Altherma EHVH04S23DAV Operation Manual preview
Altherma EHVH04S23DAV
Brand: Daikin Pages: 12
Daikin Altherma EBLQ011CAV3 Service Manual preview
Altherma EBLQ011CAV3
Brand: Daikin Pages: 140
Daikin DRC036 Installation Instructions Manual preview
DRC036
Brand: Daikin Pages: 56
Daikin DCG Series Installation And Maintenance Manual preview
DCG Series
Brand: Daikin Pages: 38
Daikin DCG Series Installation Instructions Manual preview
DCG Series
Brand: Daikin Pages: 60
Daikin SUPER MULTI NX FTXS09LVJU Installation Manual preview
SUPER MULTI NX FTXS09LVJU
Brand: Daikin Pages: 14
Daikin MCK75JVM-K Service Manual preview
MCK75JVM-K
Brand: Daikin Pages: 94
Daikin Altherma 3 R ECH2O User Reference Manual preview
Altherma 3 R ECH2O
Brand: Daikin Pages: 68
Daikin Altherma EHVZ04S18CB Installer'S Reference Manual preview
Altherma EHVZ04S18CB
Brand: Daikin Pages: 92
Daikin FTKS20CVMB Service Manual preview
FTKS20CVMB
Brand: Daikin Pages: 246
Daikin Altherma EHY2KOMB28AA User Reference Manual preview
Altherma EHY2KOMB28AA
Brand: Daikin Pages: 28
Daikin EWAQ004BAVP Operation Manuals preview
EWAQ004BAVP
Brand: Daikin Pages: 12
Daikin FDMQ12RVJU Operation Manual preview
FDMQ12RVJU
Brand: Daikin Pages: 12
Jet AFS-2000 Owner'S Manual preview
AFS-2000
Brand: Jet Pages: 11
Jet AFS-1000B Owner'S Manual preview
AFS-1000B
Brand: Jet Pages: 10

Brands by name

Popular brands

Load more brands