Huawei FusionCol8000-E24 User Manual Download Page 63

Page: 63 / 269

4.5.4.1 Preparing a Network Cable

Step 1 Crimp a network cable.

Figure 4-19 Teamwork communications cable and FE monitoring communications

cable

(1) White-and-orange (2) Orange

(3) White-and-green

(4) Blue

(5) White-and-blue

(6) Green

(7) White-and-brown (8) Brown

Figure 4-20 RS485 monitoring communications cable

(4) Blue

(5) White-and-blue

----End

4.5.4.2 CAN Te RS485 Monitoring

Step 1 Connect teamwork and monitoring communications cables.

Networking

CAN Teamwork

RS485 Monitoring

Protocol

CAN

Modbus-RTU

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands