manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 89

Chapter 3—Setting Treatment Parameters 

2008K Hemodialysis Machine Operator’s Manual Rev P 

89 

Test & Options Screen Settings 

The “Test & Options” screen is divided into two distinct sections. The left side of the screen 
is used to initiate the self test and show the results (see Chapter 2, “Testing the 2008K 
hemodialysis machine”).  The right side of the screen is available to set the machine for 
various treatment options.  Refer to the table below for descriptions of the purpose and 
functions of each button.  

 

Figure 43 – The Test & Options Screen 

The following table describes the operator-programmable features in the “Test & Options” 
screen. 

Table 20 – Test & Options Screen Buttons 

Button 

Function 

 

This test will initiate both the pressure holding tests (PHT) and the alarm 
test functions. 

 

The user can choose to do a Pressure Holding Test with this button. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды