Главная
/
Fresenius Medical Care
/
DIASAFE 2008 K
/
Руководство оператора

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться

Страница: 159 / 240

Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 159

Chapter 6—Alarms and Troubleshooting

159

2008K Hemodialysis Machine Operator’s Manual Rev P

Message

Purpose of Message

Type

Action Required

Dialysate flow is off

Dialysate flow is necessary to run an
OLC test.

Advisory

Do not attempt to run an OLC test unless the dialysate flow is set
between 300 – 800 ml/min

Dialysate flow unstable

When attempting to start an OLC test,
certain conditions are necessary,
including stable dialysate flow rate.

Advisory

Wait a minute or so and start the OLC test again.

Dialysis

Machine is currently in dialysis mode.

Advisory

Advisory message only. No action is required.

Dialysis Paused

In dialysis mode, Tx clock is paused.

Advisory

Status line advisory message only. No action is required.

Dialyzer Connected?

Indicates that one of the following
conditions exist:



Test

button selected but the

dialyzer supply and return
lines are not in the shunt.



Dialyzer

supply and return

lines are on the shunt but
blood is sensed and the blood
flow is on.

Advisory

To proceed, either:
Connect the dialyzer supply and return lines to the shunt if the
procedure requires them to be connected at this time
Or,
Connect the dialyzer supply and return lines to the dialyzer if the
procedure requires them to be connected at this time.

Note

: This message may also briefly appear if the blood

pump rate is set too low during setup. Raise the rate to at
least 100 ml/min when the blood pump is running.

Diasafe Test Failed

This message advises the operator of
the status of the Diasafe self test

Warning

Press the

RESET

key to clear the message. Rerun the test. If test

fails again return the blood to the patient if alarm occurs during
treatment. Take the machine out of service and alert a qualified
service technician to replace the Diasafe filter if necessary

Diasafe Test Passed

This message advises the operator of
the status of the Diasafe self test

Advisory

Press the

RESET

key to clear the message

Diasafe Test Recovery

This message advises the operator of
the status of the Diasafe self test

Advisory

Advisory message only. No action is required.

E.01 (Arterial or SN
Blood Pump Message)

EPROM CRC error

Alarm

If this message occurs, in dialysis mode, return the blood to the
patient if during a treatment. Take the blood pump module out of
service and alert a qualified service technician.

E.02 (Arterial or SN
Blood Pump Message)

Flash ROM CRC error

Alarm

If this message occurs in dialysis mode, return the blood to the
patient if during a treatment. Take the blood pump module out of
service and alert a qualified service technician.

E.03 (Arterial or SN
Blood Pump Message)

RAM check error

Alarm

If this message occurs in dialysis mode, return the blood to the
patient if during a treatment. Take the blood pump module out of
service and alert a qualified service technician.

«
...
157
158
159
160
161
...
»

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды