manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 154

154 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Chapter 6—Alarms and Troubleshooting 

BPM: Cuff Press High 

Blood pressure cuff is above 320 mm 
Hg for adult or above 220 mm Hg for 
pediatric mode. 

Blood 

Pressure 

Alarm 

Press the 

Stat/Deflate

 key to deflate the cuff.  Observe the patient for 

physiologic changes.  Indicates a hardware malfunction.  If problem 
persists, remove cuff and alert a qualified service technician. 

BPM: Cuff Press Low 

Blood pressure cuff is below 10 mm 
Hg. 

Blood 

Pressure 

Alarm 

Check for loose connection in the inflation system. Indicates a 
hardware malfunction.  If problem persists, remove cuff and alert a 
qualified service technician.    

BPM: Diastolic High 

The diastolic blood pressure reading 
is above the set Upper Diastolic alarm 
limit. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes. Treat patient as 
symptoms warrant.   

BPM: Diastolic Low 

The diastolic blood pressure reading 
is below the set Lower Diastolic alarm 
limit. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes. Treat patient as 
symptoms warrant.   

BPM: Measure > 90 sec 

The blood pressure test has been in 
progress for more than 90 seconds. 

Blood 

Pressure 

Alarm 

Press 

Stat/Deflate 

key to deflate the pressure cuff.  Check the 

patient for signs for physiologic changes.  Indicates a hardware 
malfunction.  If problem persists, remove cuff and alert a qualified 
service technician.  

BPM Motion Detected 

Movement of the patient, cuff tubing, 
or some other pressure on the 
detection system. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes. Treat patient as 
symptoms warrant.   

BPM: Not Communicating  Blood pressure module is not 

communicating with the machine 

Blood 

Pressure 

Alarm 

If problem persists, alert a qualified service technician. 

BPM Not Deflating 

Obstruction in inflation system or 
valve in blood pressure module 
malfunction. 

Blood 

Pressure 

Alarm 

1)  Remove kink in line to cuff. 

2)  May indicate a hardware malfunction.  If problem persists, 

remove cuff and alert a qualified service technician. 

BPM: Oscil Wave Check 

The diastolic blood pressure reading 
is close to or greater than the systolic 
pressure reading. 

Blood 

Pressure 

Alarm 

Indicates a hardware malfunction.  If problem persists, remove cuff 
and alert a qualified service technician. 

BPM: Pulse > 100 

Patient’s heart rate is above 100 
beats per minute. 

Blood 

Pressure 

Alarm 

Observe the patient for physiologic changes. Treat patient as 
symptoms warrant.  May also indicates a hardware malfunction. 

 
 
 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды