manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 156

156 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Chapter 6—Alarms and Troubleshooting 

BVM No Communication 

The BVM module has lost 
communication with the 2008K 
system. 

Alarm 

Press 

RESET

 to clear the message.  BVM will no longer pass 

information to the 2008K monitor until power has been turned off and 
back on.  If alarm is not cleared, return the blood to the patient if 
alarm occurs during treatment. Take the machine out of service and 
alert a qualified service technician. 

Chem not Connected? 

The red acid connector is still 
connected to the red rinse port 

Warning 

Connect the red (acid) connector into its correct configuration for the 
operation selected. 

Concentrate Connected? 

The red acid connector is not 
connected to the concentrate 
container. 

Warning 

Connect the red (acid) connector to the acid/acetate supply. 

Cond Offset Failure 

Electronic self-test failure. 

Alarm 

Turn machine power Off and back On. If alarm is not cleared, take 
the machine out of service and alert a qualified service technician. 

Cond Ref Failure 

Electronic self-test failure. 

Alarm 

Turn machine power Off and back On. If alarm is not cleared, take 
the machine out of service and alert a qualified service technician. 

Conductivity High 

The actual or measured conductivity 
has exceeded the high conductivity 
alarm limit.  The machine is in bypass 
mode. 

Dialysate 

Alarm 

1)  Check for the prescribed baseline Na

+ 

and

 

Bicarbonate values on 

the “Dialysate”

 

screen and re-enter the correct value for any 

erroneous values.   

 

Note

: The SVS must be off before attempting to adjust 

any parameter on this screen.  

2)  Check that the concentrates are properly mixed and in their 

proper containers.  Remix concentrates as needed. 

3)  Allow five minutes for conductivity to reach the prescribed level 

and adjust the conductivity alarm limit window if necessary (see 
“Conductivity Limits” on page 69.  

4)  Verify that there is flow out of the drain.  

5)  Replace the concentrates if it appears that the fluid is being 

pulled in, but the conductivity is still high.  After the prescribed 
conductivity is reached, verify the conductivity and the pH using 
independent testing devices.  

If unable to attain prescribed conductivity, discontinue treatment and 
alert a qualified service technician. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды