manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 122

Chapter 4—Monitoring the Treatment 

122 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Removing the Dialyzer 

There are two procedures for removing the dialyzer depending on whether your facility 
reuses dialyzers. Follow the appropriate procedure for your situation. 

If Reuse is practiced 

The dialysate compartment should not be emptied prior to cleaning the dialyzer.  In such 
cases: 

1.

 

Open the shunt door and place the dialyzer connectors on the shunt. Close the shunt door. 

2.

 

Cap the dialyzer ports with the caps supplied with the dialyzer and process dialyzer as per 
unit protocol 

3.

 

Discard the bloodlines and transducer protectors according to facility policy 

4.

 

Clean or disinfect machine according to routine cleaning and maintenance procedures 
described in “Disinfection and Maintenance,” on page 124. 

If Reuse is not practiced  

To remove the fluid in the dialysate compartment:   

1.

 

Open shunt interlock door 

2.

 

Return blue dialyzer connector to shunt interlock 

3.

 

Reposition the dialyzer so that the red, outlet port is at the bottom 

4.

 

Close the shunt interlock door.  Message “Emptying” will be displayed. 

5.

 

Drain the dialysate compartment.  The dialyzer is empty as soon as there is air in the 
outlet line or an “Emptying stopped” message appears. 

6.

 

Open the shunt interlock door, remove the red dialyzer connector from the dialyzer and 
place it on the shunt.  Close the shunt interlock door. 

7.

 

Discard the bloodlines, transducer protectors, and dialyzer according to facility policy. 

8.

 

Insert the concentrate wands into their proper rinse ports.  The “Select Program” screen 
appears on the display screen. 

9.

 

Clean or disinfect the exterior of the machine according to routine cleaning and 
maintenance procedures described in “Disinfection and Maintenance,” on page 124. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды