manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 126

Chapter 5—Disinfection and Maintenance 

126 

2008K Hemodialysis Machine Operator’s Manual Rev P 

 
 

Procedure 

Frequency 

Description 

 

Page 132 

Weekly 

The 

Chemical / Rinse

 button runs a program that disinfects the 

hydraulic system using a chemical disinfectant followed by an 
immediate water rinse to clear the system of residual disinfectant.  
The Chemical / Rinse program should be used when disinfecting 
with corrosive chemicals, such as bleach, that could damage the 
hydraulic components if left in contact for prolonged periods. 

 

Page 134 

Per Unit 

Protocol 

The Chemical / Dwell program is designed for disinfecting the 
hydraulic system using a non-corrosive chemical disinfectant, such 
as formaldehyde.  This program is intended for use with chemicals 
that are not harmful to the internal components after prolonged 
exposure and, hence, do not require the system to be rinsed with 
water immediately afterward.  

 

Page 127

 

Weekly 

Clean and disinfect bicarbonate concentrate jugs and suction cap 
wands per facility protocol. 

Additional Disinfection Requirements 

In addition to the routine cleaning and disinfection tasks listed in the previous table, 
additional disinfection is required for the following situations:   

 

Each time the water treatment system is disinfected 

When the water treatment system and distribution piping are disinfected, each dialysate 
delivery machine should be placed in the Rinse program to draw disinfectant into the 
machine through the inlet lines.  Check for residual disinfectant prior to use for dialysis. 

 

After contamination of transducer protector 

Disinfect the connectors and replace the internal transducer protector if there is 
evidence of leakage past the external transducer protector on the venous or blood pump 
modules.  Disinfect associated parts. 

 

After a dialyzer blood leak  

The machine should be disinfected prior to the next treatment if a blood leak alarm 
occurred. 

 

 

Warning! 

The protocol for disinfection is determined by the facility and its medical 

director.  When chemicals are used internally, machines must be thoroughly rinsed and 
tested for residual disinfectant before using the machine for treatment.  Follow the 
instructions of the chemical manufacturer for residual testing.  If the machine is chemically 
disinfected daily, we recommend that it also be heat disinfected at least once per week. 

 
 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды