manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 183

Chapter 6—Alarms and Troubleshooting 

183 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Message 

Purpose of Message 

Type 

Action Required

 

UF Pump Alarm 

UF pump is not connected or is not 
pulsing properly. 

Alarm 

Press 

RESET

 to reset the alarm.  If unable to clear the alarm, return 

the blood to the patient if alarm occurs during treatment. Take 
machine out of service and alert a qualified service technician. 

UF Rate Error 

A calculation error has been detected 

Alarm 

Reset the UF parameters 

UF Removed cleared 

This temporary message is displayed 
when the Tx clock is turned on the 
first time after the 

New TX

 key was 

pressed.  The UF removed has been 
set to 0. 

Advisory 

No action necessary. 

UF Removed not cleared 

This temporary message is displayed 
when the Tx clock is turned on other 
than the first time after the 

New TX

 

key was pressed.  The UF removed 
has been not been set to 0. 

Advisory 

No action necessary. 

Upper Dia. has been set 
to Min [Max] 

The operator has attempted to set the 
upper diastolic pressure limit higher or 
lower than allowed.  The machine has 
set the limit to the highest or lowest 
value allowed. 

Dialog 

Message 

Verify that the limit setting is acceptable 

Upper Pulse has been set 
to Min [Max] 

The operator has attempted to set the 
upper pulse rate limit higher or lower 
than allowed. 

Dialog 

Message 

The machine has set the limit to the highest or lowest value allowed.  
Verify that the limit setting is acceptable 

Upper Sys. has been set 
to Min [Max] 

The operator has attempted to set the 
upper systolic pressure limit higher or 
lower than allowed. 

Dialog 

Message 

The machine has set the limit to the highest or lowest value allowed.  
Verify that the limit setting is acceptable 

Valve 43 Failure 

Valve 43 has remained open too long 

Alarm 

Turn machine power off and back on. Just before beginning dialysis, 
verify that the dialysate flow can be turned off and back on.  Do not 
initiate or continue dialysis if this cannot be done. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды