manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 219

Machine Specifications 

2008K Hemodialysis Machine Operator’s Manual Rev P 

219 

Proportional Mixing System  

 

Acid 

Volumetric, selectable: 
1:34  
1:44  
1:35.83 
1:35.1 
Note: Citrasate® is for use with 1:44 concentrates only. 

Acetate 

1:34 

Adjustment Range 

130 to 155 mEq/L Na

+

 

Bicarbonate  

Volumetric, selected with associated acid ratio  
1:27.46 
1:19.13 
1:25.16 
1:27.6 

Adjustment Range 

20 to 40 mEq/L Bicarbonate (post-reaction, after mixing with 
the acid and purified water).

 

Monitoring Conductivity 

Average Accuracy: ± 1.5% 
Method: Temperature compensated electronic conductivity 
meter with adjustable alarm limits. 
Temperature compensated conductivity display with 
automatically set alarm windows ±0.5 mS/cm around 
calculated conductivity.  User can adjust an additional ±0.5 
mS/cm within this range. Conductivity is based on the 
concentrates’ compositional data entered in the Dialysate 
screen at the standard temperature of 25 

C. 

Range of Display 

10.0 to 17.0 mS/cm. At 25 °C. Alarm limits will not go below 
12.5 or above 16.0 mS/cm. 

Dialysate Heating

  

Nominal Value of Temperature 
 

35 to 39 °C  Accuracy: ± 0.3 °C (measuring accuracy under 
calibration conditions for a dialysate flow of 500 ml/min) 
(selectable in 0.1 °C steps)

 

Temperature Display 

Range 35 to 39 °C with alarm limit window automatically 
adjusted to 2 °C above and below set point. Alarm window 
will not go below 30° or above 41 °C. Heater 1.3 kW, 
electronically controlled. 

Heat Disinfection 

 

Temperature 

83 

 8 °C at NTC 3  

Flow Rate 

600 ml/min.  
Pre-rinse either 7 min @ 600 ml/min or 20 min @ 300 ml/min 
(user selectable).  10 min @ 600 ml/min for DIASAFE PLUS 
equipped machines. 

Time 

Between 10 and 60 minutes (internally selectable) 

Auto Heat Disinfect Pre-rinse Time 

Between 15 and 30 minutes (user selectable) @ 600 ml/min 
(standard) or 350 ml/min (extended pre-rinse).  Note: Heater 
is off during pre-rinse. 

Auto Heat Disinfect Pressure 

25 psi < pressure < 90 psi 
Note: Silicon inlet/drain tubing set #M38512 must be used 
with this option 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды