manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 230

Appendix C—The 2008K@home Hemodialysis Machine 

230 

2008K Hemodialysis Machine Operator’s Manual Rev P 

  

 

Figure 75 – 2008K and 2008K@home “Home” Screens 

Table 36 – Software Screen Differences 

Item 

2008K 

2008K@home 

Setting Treatment 
Parameters 

Set on various screens, 
organized by screen-
buttons along bottom of 
display screen 

Treatment parameters are grouped on 
the “Rx Parameter” screen (accessed 
from the “Select Program” screen) and 
programmed all at once outside of 
Dialysis Mode. 

The UF goal is calculated based on the 
UF Time (called ‘Tx Time’) and patient 
weight entered in the guided “Tx Set up” 
screens. 

Testing the 
Machine 

All tests are performed on 
the “Test & Options” 
screen 

Tests are performed during guided 
setup; during treatment, tests are 
available on the “Help” screen 

Setting Dialysate 
Parameters 

The “Dialysate” screen is 
accessed by touching the 

Dialysate

 screen-button 

along the bottom of the 
Touchscreen 

Concentrates are selected in the “Rx 
Parameters” screen. 

Concentrates are confirmed in the 
guided set up process.  Touching the 

Conductivity

 button on the “Home” 

screen will display these settings if limits 
need to be adjusted. 

UF and SVS 
Profiles 

Available from the 
“Home” screen 

The ‘In Center’ option must be set in 
order to display the Dialysis Mode 

SVS 

Profile

 and 

UF Profile

 buttons. 

To set the ‘In Center’ option: in Service 
Mode, on the “Options: Treatment 
Options” screen, touch the 

In Center Set 

up

 toggle button to set it to ‘In Center’ 

then press the 

CONFIRM

 key. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды