manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 186

Chapter 6—Alarms and Troubleshooting 

186 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Replacing the Diasafe Plus Filter 

The Diasafe Plus filter is intended for the preparation of ultra-pure dialysate.  If the machine 
has a Diasafe Plus filter, it should be replaced at least every 90 days (3 months).  You must 
also replace the filter if the Diasafe test fails or shows an external leak.  To replace the 
Diasafe Plus filter: 

 

Warning!

 The use of the Diasafe Plus filter does not reduce the need for routine 

disinfection of your machine and RO system or routine monitoring of the chemical and 
bacterial water quality.  The disinfection procedure is unchanged with the Diasafe Plus filter 
installed.

 

 

Warning!

 The Diasafe Plus filter can only be used in hemodialysis machines fitted with 

Diasafe Plus Diafix lock system kits.

 

 

Caution

:  Be sure to remove the plastic tabs on the Diasafe Plus filter inlet and outlet before 

inserting the new filter in the machine.

 

 

Note

: If you instead have the DIASAFE Filter (located inside your machine), refer to P/N 

490039: Diasafe Filter Operator’s Instructions.

 

1.

 

Lift up the lock levers on the left side of the filter mount and slide used Diasafe Plus filter 
up and out.  Follow your clinic’s instructions for disposal. 

2.

 

Fit the fresh Diasafe Plus filter in the groove at the top of the mount and slide it down 
until it clicks into place.  Push the lock levers down again to lock the filter into its mount. 

3.

 

Test the new Diasafe Plus filter: From the “Test & Options” screen (see page 89), select 
the 

Pressure Test

 button and press 

CONFIRM

 to start the test.  When the Pressure 

Holding test has passed, touch the 

Diasafe Test

 button and press 

CONFIRM

 to start the 

test. 

 

Warning!

 If the machine fails any of the tests and the cause cannot be corrected, or if it fails 

later tests, it should not be used for treatment. Have the machine checked by a qualified 
technician to correct the problem. 

 

Warning!

 After replacing the Diasafe Plus filter, run a Heat Disinfect to disinfect the 

machine. 

Replacing the 9-Volt Battery 

Replace the machine’s 9-Volt battery if the battery test fails in the Alarm test.  Follow the 
instructions below: 

1.

 

Turn the machine OFF.  Locate the battery on the back of the machine and push the black 
battery loading cartridge in and to the left.  The battery cartridge will pop forward.  Slide 
the cartridge out. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды