manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 146

146 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Chapter 6—Alarms and Troubleshooting 

 

Acid Pump Alarm 

This is a pump failure warning.  

Warning 

A single occurrence is not a problem if the machine automatically 
resets.  If the problem persists for longer than one minute or occurs 
repeatedly, turn power off and back on. If warning is not cleared, 
return the blood to the patient if alarm occurs during treatment. Take 
the machine out of service and alert a qualified service technician. 

Acid Pump Always EOS 

This is a pump failure warning.  

Warning 

A single occurrence is not a problem if the machine automatically 
resets.  If the problem persists for longer than one minute or occurs 
repeatedly, turn power off and back on. If warning is not cleared, 
return the blood to the patient if alarm occurs during treatment. Take 
the machine out of service and alert a qualified service technician. 

Acid Pump No EOS 

This is a pump failure warning.  

Warning 

A single occurrence is not a problem if the machine automatically 
resets.  If the problem persists for longer than one minute or occurs 
repeatedly, turn power off and back on. If warning is not cleared,  
return the blood to the patient if alarm occurs during treatment. Take 
the machine out of service and alert a qualified service technician. 

Act Blood Pump Failed 

Electronic self-test failure. 

Alarm 

Turn machine power off and back on. If alarm is not cleared,  return 
the blood to the patient if alarm occurs during treatment. Take the 
machine out of service and alert a qualified service technician. 

Act Board CRC Error 

Electronic self-test failure. 

Alarm 

Turn machine power off and back on. If alarm is not cleared, return 
the blood to the patient if alarm occurs during treatment. Take the 
machine out of service and alert a qualified service technician. 

Act BYP Valve Fail 1 

Electronic self-test failure. 

Alarm 

Turn machine power off and back on. If alarm is not cleared, return 
the blood to the patient if alarm occurs during treatment. Take the 
machine out of service and alert a qualified service technician. 

Act BYP Valve Fail 2 

Electronic self-test failure. 

Alarm 

Turn machine power off and back on. If alarm is not cleared, return 
the blood to the patient if alarm occurs during treatment. Take the 
machine out of service and alert a qualified service technician. 

Actuator BD no Echo 

Functional to Actuator board 
communication problem 

Alarm 

Turn machine power off and back on. If alarm is not cleared, return 
the blood to the patient if alarm occurs during treatment. Take the 
machine out of service and alert a qualified service technician. 

Adjusting TMP 

The operator has chosen to relieve 
the TMP after a TMP alarm 

Advisory 

No action necessary. 

 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды