Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 166

Страница: 166 / 240

166

2008K Hemodialysis Machine Operator’s Manual Rev P

Chapter 6—Alarms and Troubleshooting

Flow Recirc Error 2

Dialysate flow problem.

Warning

A single occurrence is not a problem if the machine automatically
resets. If the problem persists for longer than one minute or occurs
repeatedly:

1) Check the water supply flow to the machine.

2) Check that the Dialysate Flow is on.

3) Set Dialysate Flow in the “Home” screen to 500 ml/min and verify

that the flow from the drain line is 500 ml/min



50 ml/min.

4) Turn the power off and on. If warning is not cleared, return the

blood to the patient if alarm occurs during treatment.

5) Take the machine out of service and alert a qualified service

technician.

Front Panel No Comm

The processor is unable to
communicate with the front panel

Opening

Screen

Message

Turn machine power off and back on. If failure repeats, return the
blood to the patient if alarm occurs during treatment. Take the
machine out of service and refer to a qualified service technician.

Heparin Dwell Complete

The five minute timer for a manual
heparin bolus has elapsed.

Advisory

Press the

RESET

key to clear the message. The Status Light will

stop flashing.

Greater than max. value

Entered parameter is larger than
allowed

Dialog

Message

Verify that the maximum value is acceptable. Press

CONFIRM

clear message and accept the maximum allowed value.

Heat Relay Test Fail

Electronic self-test failure.

Alarm

Turn machine power off and back on. If alarm is not cleared, take the
machine out of service and alert a qualified technician.

Heparin Pump Alarm

The Heparin pump is encountering
resistance.

Alarm

1) Check the heparin line for clamps or kinks and correct.

2) Check the heparin syringe for adequate amount of heparin and

correct.

3) Ensure the correct type of syringe is loaded and locked in place

properly.

4) Press

RESET

to clear the alarm and restart the heparin pump.

5) If the alarm will not reset or continues to alarm intermittently,

return the blood to the patient if alarm occurs during treatment.

6) Take the heparin pump out of service and alert a qualified service

technician.

Note

: An alarm will sound

when the heparin pump has
reached the end of its
stroke during normal
operation.

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды