Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 150

Страница: 150 / 240

150

2008K Hemodialysis Machine Operator’s Manual Rev P

Chapter 6—Alarms and Troubleshooting

Blood Leak?

The blood leak detector has detected
the presence of blood or air in the
dialysate.

Blood
Alarm

1) Press

RESET

to reset the alarm. If allowed by facility policy,

press

Override

to continue dialysis if the machine cannot be

reset.

2) Check dialysate fluid for presence of blood with a blood leak test

strip.

If test is negative

, recheck with a new blood leak test strip. If

negative after three checks, follow steps below:

Press

Override

to run the blood pump for up to 3 minutes while

troubleshooting the alarm.

Check the dialyzer supply and return lines for air leaks, especially at
the dialyzer connectors and the filter screen in the dialyzer return line.
Press

RESET

to reset alarm.

If unable to reset the alarm, return the patient’s blood according to

procedure below (test positive) and alert a qualified service
technician.

Note

: Air or disinfectants

containing peracetic acid
may cause a false alarm.

Warning

! During an

override, the machine’s
blood leak detector is
inactive. You must monitor
the treatment.

If test is positive

, proceed according to facility blood leak policy. If

facility policy is to return patient’s blood, follow the steps below.

1) Press

RESET

to reset all other blood flow alarms.

2) Press

Override

to enable the blood pump to run and return

patient’s blood per unit protocol.

Note

: Override will activate the blood pump for about

three minutes while a blood leak alarm exists. Press

Override

again if more time is needed to return the

patient’s blood.

Blood Pump +5 V Error

+ 5 volts is outside the allowable
range

Alarm

See message E.10

Blood Pump +12 V Error

+ 12 volts is outside the allowable
range

Alarm

See message E.07

Blood Pump -12 V Error

- 12 volts is outside the allowable
range

Alarm

See message E.09

Blood Pump +24 V Error

+ 24 volts is outside the allowable
range

Alarm

See message E.08

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды