manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 176

176 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Chapter 6—Alarms and Troubleshooting 

Recirculating Done 

A prompt to the operator that the 
recirculation process is done. 

Advisory 

Press 

RESET

 to clear the advisory message. 

Recirculating Stopped 

Recirculation has been stopped 
because blood is sensed or the 
dialyzer supply and return lines are on 
shunt. 

Warning 

Inspect the configuration of the dialyzer supply and return lines and 
extracorporeal blood circuit. Correct any irregularities.  If the message 
is not cleared, take the machine out of service and alert a qualified 
service technician. 

Release CONFIRM to 
stop 

This message is a prompt for the 
operator to release the 

CONFIRM

 key 

to stop priming the heparin line. 

Dialog 

Message 

Release the 

CONFIRM

 key.  

Rel. Blood Volume Low 

The BVM module has reported a 
relative blood volume below the lower 
limit. 

Alarm 

Press 

RESET

 to clear the message.  Evaluate the fluid status of the 

patient. 

RESET to adjust TMP 

The TMP exceeded the hard alarm 
limits.  The operator is given the 
option to relieve the pressure to bring 
the TMP within limits. 

Warning 

Press the 

RESET

 key to reset the TMP alarm limits.  Press and hold 

the

 Override

 key to re-center the limits. 

 

Warning!

  Adjusting the 

TMP repeatedly will 
decrease the UF removed 
from the patient. 

 

Warning

! Rising TMP may indicate a leak in the balancing 

system and should be investigated. 

Reset Treatment? 
CONFIRM or Escape 

The 

New TX

 key has been pressed 

Advisory 

To reset treatment parameters for a new treatment, press the 

CONFIRM

 key.  To cancel, press the 

Escape

 key. 

Resetting, Try Again 

Blood pressure module resetting  

Warning 

Wait until blood pressure module completes resetting and retry blood 
pressure reading. 

Retry > Press = XXX 

The cuff pressure is too low to 
measure the blood pressure.  The cuff 
pressure is XXX mmHg. 

Dialog 

Message 

No action necessary 

Reverse bloodlines 

This message is a prompt for the 
operator reverse the bloodlines for the 
Access Flow test 

Warning 

To proceed with the Access Flow test, reverse the bloodlines and 
press 

CONFIRM

.   

Rinse Cond High 

The Reverse Osmosis (RO) water 
inlet conductivity is too high. 

Opening 

Screen 

Message 

Press the 

RESET

 key to clear the message. Perform a Rinse cycle. If 

alarm is not cleared, take the machine out of service and alert a 
qualified service technician. 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды