manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 133

Chapter 5—Disinfection and Maintenance 

2008K Hemodialysis Machine Operator’s Manual Rev P 

133 

 

Figure 61 – The Chemical Rinse Screen 

5.

 

Connect the red connector to a jug containing the chemical disinfectant and press 

CONFIRM

 when prompted. 

6.

 

Water pre-rinse will start.  Remaining Pre-rinse Time meter box will count down.   

7.

 

When Remaining Pre-rinse Time meter box reads 0:00, chemical rinse will start after a 
delay.  Remaining Time meter box will count down. 

 

 

Note

: Visually confirm that disinfectant has been pulled into the machine.  

 

8.

 

When the Remaining Time meter box reads: 0:00, remove the acid connector from the 
disinfectant jug and insert it into the acid rinse port when prompted.  Post rinse will start 
and Remaining Post Rinse Time meter box counts down. 

9.

 

Press 

CONFIRM

 to exit. 

 

 

Warning! 

Test for residual disinfectant prior to starting treatment following a chemical 

disinfection. 

 

 

Note

: The machine will automatically perform a Diasafe test after the Chemical Rinse 

program completes (Functional board software version 3.36 or later). 

 

 
 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды