manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 168

168 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Chapter 6—Alarms and Troubleshooting 

Hold CONFIRM to Prime 

In heparin screen after selecting 
prime must press and hold confirm to 
prime heparin line. 

Dialog 

Message 

Press and hold 

CONFIRM

 to prime the heparin line. 

I2C Read Time Out 

I2C Bus Read Error 

I2C Bus Read Too Long 

I2C Byte Write Error 

Functional to I2C EEPROM 
communication problem.  

Alarm 

Turn machine power off and back on. If alarm is not cleared, return 
the blood to the patient if alarm occurs during treatment. Take the 
machine out of service and alert a qualified service technician. 

In bypass for 8 min 

Press 

RESET

 to clear the message 

Advisory 

The machine was in bypass for about eight minutes.  This may 
extend the time necessary to complete the treatment or rinsing of 
germicide.  Press 

RESET

 to clear the message. 

 

Warning!

  If rinsing germicide from the machine or 

dialyzer when this occurs, additional time will be 
necessary to fully rinse the germicide from the dialyzer.  
Always check for residual germicide using the 
appropriate approved residual test method. 

INTERRUPT RINSE? 
Escape or CONFIRM 

Press 

CONFIRM

 to interrupt rinse. 

Dialog 

Message 

Press 

CONFIRM

 to accept or press escape to cancel. 

Interrupted 

The selected Rinse program has 
been interrupted.  

Warning 

Re-insert the dialysate connectors into the proper rinse ports.  To 
continue the Rinse or other program, press 

CONFIRM

, then reselect 

the desired program.  

Invalid Data Entry for 
[item] 

Entry value for [item] is out of range 

Dialog 

Message 

Set appropriate value for [item]  

Invalid UF Rate 

Entry value for goal is out of range. 

Dialog 

Message 

Readjust rate 

Invalid UF Time 

Entry value for goal is out of range. 

Dialog 

Message 

Readjust time 

 
 
 
 
 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды