manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 172

172 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Chapter 6—Alarms and Troubleshooting 

Must Run Test First 

The Forced Test is required before 
proceeding with UF or SVS.

 

Warning 

To proceed with the selected operation, run the Pressure and Alarm 
tests.  For more information, see Chapter 2 “Testing the 2008K 
hemodialysis machine.” 

Need Blood Sensed 

An action has been initiated that 
requires that blood is sensed.  

Dialog 

Message 

Verify venous bloodline is in the Optical Detector.   

Neg. Access Flow value 

This message is an advisory 
message that the Access Flow test 
result was a negative value.  A 
positive value is expected.   

Warning 

This can occur if the bloodlines were initially connected in the 
reversed position.  Press 

CONFIRM

 to clear the message. Check that 

the bloodlines are properly connected and repeat the Access Flow 
test. 

Negative error AF value 

This message is an advisory 
message that the  Access Flow test 
result was an erroneous value 

Warning 

Press 

CONFIRM

 to clear the message. Check that the bloodlines are 

properly connected and repeat the Access Flow test.  Press 

CONFIRM

 to clear the message. 

New Art Limits chosen 

This message advises the operator 
that a new set of arterial limits has 
been set. 

Advisory 

Advisory only.  No action is required. 

New features loaded,  
Power Off,  Replace 
EEPROM 

Advisory message when uploading 
hardware key option 

Advisory 

Put the original calibration EEPROM in IC 20 and restart the 
machine. 

New TMP Limits Chosen 

This message confirms that a new set 
of TMP limits have been set. 

Advisory 

Advisory only.  No action is required. 

New Venous Limits? 

This message is a prompt for the 
operator to set new venous alarm 
limits. 

Advisory 

To set new venous alarm limits, press 

RESET

 and hold.  

New Ven Limits Chosen 

New venous alarm limits are set 

Advisory 

Advisory only.  No action is required 

No Air Detector Alarm 

The 

Prime

 key has been pressed. A 

level detector alarm must exist for this 
function to occur 

Advisory 

If the venous chamber has fluid detected, the prime function will not 
occur.  Press 

RESET

 to start the blood pump.  If a level detector 

alarm occurs, then press the 

Prime

 key. 

 
 
 
 
 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды