manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 131

Chapter 5—Disinfection and Maintenance 

2008K Hemodialysis Machine Operator’s Manual Rev P 

131 

Heat Disinfection  

The Heat Disinfect program disinfects the machine by running hot water (about 80 

C) 

through the machine.  The water recirculates at a program-controlled flow of about 400 
ml/min.  The program time can be set internally to run between 10 and 60 minutes. The timer 
starts as soon as the temperature of the water reaches 80 °C. 

To run the Heat Disinfect program: 

1.

 

Ensure that both dialysate lines are on the shunt and both concentrate connectors in their 
respective ports.   

2.

 

From the “Select Program” screen, touch 

Heat

 

Disinfect

 to start the Heat Disinfect 

program.  The “Heat Disinfect” screen appears in the control panel display (see Figure 
60). If the machine was not rinsed prior to this, it will automatically run a short rinse 
(seven minutes) or an extended rinse (20 minutes) depending on how the machine was 
configured in Service Mode. 

 

Figure 60 – The Heat Disinfection Screen 

 

Warning!

 During the heat disinfection cycle, it is not uncommon to see steam emitting from 

the vent tubing at the back of the machine.  This steam may cause burns if contacted.  Also, 
the

 

temperature of the dialysate lines and drain line can get as hot as 69 °C (156 °F). Please 

use care. 

3.

 

After the heat disinfection is complete, if the machine is not configured to automatically 
turn off at the completion of the cycle, press 

CONFIRM

 to exit when prompted. 

 

 

Note

:

 

The drain line is subjected to a lower temperature and shorter heat cycle than the rest 

of the machine. If you are unable to completely clean biofilm from the drain line, select the 
“Extended Pre-rinse” option in Service Mode.  If necessary, replace the drain line. 

 

Note

: Cooling time can be shortened by running the Rinse program, which will flush the 

machine with 37 °C water.  Do not cool the machine with the Rinse program unless the 
machine will be used immediately afterwards.

 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды