manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 78

Chapter 3—Setting Treatment Parameters 

78 

2008K Hemodialysis Machine Operator’s Manual Rev P 

 

 

Note

: The “None” profile performs ultrafiltration at a constant rate.  It does not mean that no 

ultrafiltration will occur. 

The maximum UF rate is displayed for the selected profile, UF Goal, and UF Time. If the 
maximum UF Rate is too high (beyond the configuration of the machine), a message appears 
in the Dialogue Box located in the upper, right corner of the screen.  The operator has the 
option of increasing the UF Time, reducing the UF Goal, or selecting another profile.   

To change the profile, select the corresponding profile button.   

To change the time, touch the 

UF Time

 button.   

To change the UF goal, touch the 

UF Goal

 button.  The maximum ultrafiltration rate, based 

on the UF Goal, Time & Profile, will be calculated and displayed in the Maximum UF-Rate 
display.   

When all ultrafiltration parameters are satisfactory, press 

CONFIRM 

to save the changes, 

then exit from the “UF Profile” screen.  The machine will apply the new UF profile to the 
remaining UF time in twelve equal segments. 

 

 

Note

: With software versions prior to 3.12, if any UF parameter is changed after a UF 

profile program has started, a new UF profile is started from the beginning of the indicated 
Profile for the displayed UF time.  Beginning with version 3.12, the UF goal may be 
changed during a profile.  The UF rates will be automatically recalculated to achieve the 
desired UF Goal.  Changing the UF Profile or UF time will cause a new profile to begin. 

 

Sequential Dialysis  

Sequential dialysis refers to a two-stage treatment in which one of the stages consists solely 
of ultrafiltration without dialysate flow (no diffusion).  This stage of the treatment is also 
referred to as “pure UF,” or “no-flow dialysis,” and is often prescribed for patients suffering 
from excessive fluid retention.  Pure UF is usually performed at the beginning of a standard 
dialysis treatment, although it can also be administered during treatment. The operator can 
start or stop the pure UF option at any time.  In pure UF, Dialysate Flow is set to 0 ml/min 
and only ultrafiltration occurs.  The 

Temperature

 button in the “Home” screen displays N/A.  

 

 

 

 

 

 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды