manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 167

Chapter 6—Alarms and Troubleshooting 

167 

2008K Hemodialysis Machine Operator’s Manual Rev P 

 

Message 

Purpose of Message 

Type 

Action Required

 

High Flow Error 

Possible balancing chamber problem. 

Warning 

A single occurrence is not a problem if the machine automatically 
resets.  If the problem persists for longer than one minute or occurs 
repeatedly:  

1)  Check the water supply flow to the machine. 

2)  Check that the Dialysate Flow is on. 

3)  Set Dialysate Flow in the “Home” screen to 500 ml/min and verify 

that the flow from the drain line is 500 ml/min 

 50 ml/min. 

4)  Turn the power off and on.  If warning is not cleared, return the 

blood to the patient if alarm occurs during treatment. 

5)  Take the machine out of service and alert a qualified service 

technician. 

High Temperature 

The actual dialysate temperature has 
exceeded the high-temperature alarm 
limit.  Machine is in bypass mode. 

Dialysate 
Alarm 

1)  Ensure that water is flowing to machine when turned on. 

2)  Check water supply to machine for excess temperature and 

correct if necessary. 

3)  If heat disinfection was recently performed, place machine in 

rinse cycle to decrease temperature. 

4)  Check the Temperature value in the “Home” screen. Re-enter it if 

necessary and allow five minutes for the temperature to stabilize.  

5)  Check that the dialysate flow at drain line is 500 ml/min ± 50 ml. 

6)  If unable to reach prescribed temperature, return the blood to the 

patient if alarm occurs during treatment.  

7)  Take the machine out of service, discontinue treatment, and alert 

a qualified service technician. 

 

Note

: If the temperature 

fluctuates between HIGH 
TEMPERATURE and LOW 
TEMPERATURE, see 
“VARIABLE 
TEMPERATURE.” 

 

 

 

Warning! 

Hemolysis of blood in the dialyzer may occur 

should the dialysate exceed a temperature of 42 °C. 
Dialysate temperatures must be maintained below this 
level.  Do not return hemolyzed blood to the patient.

 

 

Caution

:

 

Do not use the Heat Disinfect cycle until the 

machine has been repaired

.  

If you are unable to attain 

proper dialysate temperature, return the blood to the 
patient if alarm occurs during treatment. Take the machine 
out of service and alert a qualified service technician. 

 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды