manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Поделиться
Скачать
Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 123

Chapter 4—Monitoring the Treatment 

2008K Hemodialysis Machine Operator’s Manual Rev P 

123 

Removing Bloodlines from the Machine  

The arterial and venous ends of the bloodline should be clamped to avoid spillage before 
attempting to remove the lines from the system. 

 

 

Caution

: Do not forcefully pull the lines from the machine.  Damage to the machine or its 

components may result. 

To remove the bloodline from the blood pump, open the door and align the rotor by pressing 
and holding the 

Start/Stop

 key until the pump stops.  Press the clamp-panel below the rotor 

to release the left (incoming) side of the pump segment.  Pull the first couple of inches of the 
pump segment out of the pump.  Then, while keeping firm tension outward on the left 
(incoming) side of the bloodline, press and hold the 

Start/Stop

 key a second time and the 

pump segment will be released from the pump head. 

Be sure to open the door to the optical detector before pulling the line from the venous clamp 
and optical detector assembly. 

 

Содержание DIASAFE 2008 K

















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды