Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 44

Страница: 44 / 240

Chapter 2—Daily Preparation for Treatment

2008K Hemodialysis Machine Operator’s Manual Rev P

Preparing the Dialysis Delivery System

To prepare the 2008K hemodialysis machine for operation:

Press the

POWER

key on the control panel. The green light above the key will light,

and the “Select Program” screen (see Figure 19) will appear on the monitor after
approximately one minute.

Note

: If the machine is filled with disinfectant or Rinse is the only option that appears in the

“Select Program” screen, the machine must complete a rinse cycle before being used for
treatment. Touch

Rinse

to start the rinse cycle. Upon completion of rinse cycle test the

machine for any residual disinfectant according to the established guidelines of the facility.

Note

: During the power up sequence a message is displayed for a few seconds: “Press

Confirm for Service Mode”. If this is done, the machine enters the calibration screens
instead of the “Select Program” screen.

Figure 19 – The Select Program Screen

Insert the acid concentrate (red) connector into a centralized acid supply or a jug
containing sufficient acid concentrate for an entire treatment. If acetate concentrate is
being used, insert the red connector into the acetate supply.

Caution

: Be sure the jug contains enough concentrate for the entire treatment. If the jug

runs out during treatment, a condition known as “air lock” may occur, causing conductivity
problems.

If the machine is being prepared for normal dialysis, touch the

Dialysis

button on the

touch screen. The Dialysate screen will appear on the monitor (see Figure 20).

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды