Fresenius Medical Care DIASAFE 2008 K Скачать руководство пользователя страница 33

Страница: 33 / 240

Chapter 1—Overview

2008K Hemodialysis Machine Operator’s Manual Rev P

Figure 10 – The Blood Pump Module

The following table describes the operational features of the blood pump.

Table 6- Blood Pump Features

FEATURE

PURPOSE

Start/Stop Key

Starts and stops the blood pump. Opening the door will also stop the
blood pump.

Pressure Port

Line from arterial drip chamber is connected to a transducer protector
and attached here to provide arterial blood pressure readings.

Level Adjust Key Pressing the



key (level adjust key on the Blood Pump module) will

raise the level of the fluid in the arterial drip chamber.

Display Window Displays the blood flow rate setting in increments of 5 ml/min during

blood pump operation. When the door is open it displays the pump-
segment diameter in mm.

Up/Down Keys

Increases the speed of the pump when Up arrow (



) is depressed,

decreases the pump speed when Down arrow (



) is depressed. When

door is open, simultaneously press the



and



keys and then press

the





key to select the pump segment diameter.

Tubing Retainer

A spring-loaded device that secures the pump segment in place.

Display
Window

Blood Pump
Rotor

Start/Stop Key

Arterial
Pressure Port

Level
Adjust Key

Up/Down
Arrow Keys

Tubing
Retainer
Clamp-Panel

Left and
Right Yokes

Содержание DIASAFE 2008 K

















































































































































































































































Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care DIASAFE 2008 K, Руководство оператора

Результаты поиска

Содержание DIASAFE 2008 K

Отзывы:

Бренды по названию

Популярные бренды